In addition to holding the batteries, it contains small switches (Figure 9) that give you the option to change some of the factory-set operation defaults for your headset. The battery compartment on your headset control model serves two purposes. Align the screws and tighten them to secure the cover. Attach the access cover to the connector panel on the earcup that does not have the boom mic attached.Rotate the microphone boom into position so it will be near your mouth when you put on the headset.With the screw threads properly aligned, tighten the screws.Press the assembly onto the connector pins until it is fully engaged and the cable assembly is flush with the earcup.ĬAUTION: Do not apply excessive force, which may result in earcup damage.Carefully line up the connector to the small connector pins on the panel.Remove the cover to reveal the connector pins on the earcup. Use a Phillips or straight-blade screwdriver to loosen the two screws on the access cover near the bottom of the earcup where you want to attach the boom microphone.Twisting can damage the connector pins.īefore you attach the boom microphone, make sure that the cable connector and its earcup connector are clean and free of debris. Pull the cable assembly straight out from the earcup to which it is attached.ĬAUTION: Do not twist the boom microphone cable while disconnecting it.Use a Phillips or straight-blade screwdriver to loosen the two screws at the base of the boom microphone cable assembly.Removing an attached boom microphone cable These markings indicate which ear each earcup is intended to fit over. Before you remove or attach the microphone, however, be sure to note the important markings for left (L) and right (R) above each earcup. In either case, you can attach the boom microphone cable to either earcup, as preferred. The last three digits, 192, refer to the day of the year (the 192nd day of 2003).ĭecide where you want the boom microphoneĭepending on the headset configuration you purchased, your headset may arrive with the boom microphone cable attached to the left earcup or packed separately in the carton. The first digit, 3, refers to the year of manufacture (2003). Example: 031963E31920040E In this example, the date of manufacture is 3192. It is the underlined, four-digit number that begins just after the first alphabetic letter in the serial number. Your headset’s date of manufacture is an important part of your serial number. For more information on replacing the headband cushion. Be sure to include your headset serial number, which can be found on the barcode label located on the underside of the magnesium headband, underneath the headband cushion.Īfter locating your headset serial number, be sure to properly replace the headband cushion by pressing down firmly. We will use this information to provide you with appropriate advisories and updates. Please fill in the requested information and mail it to Bose. The Bose® Aviation Headset includes a product registration card in the carton. Locate the serial number for your product registration card Flexible microphone boom with continuous position adjustments.Communications cable with an integrated control module.Acoustic Noise Cancelling headset technology.The communications cable for your headset may be either straight or coiled, depending on the headset configuration you have purchased. There are also battery-powered and aircraft-powered versions. The Bose Aviation Headset is available in variations designed for general aviation and helicopter use. We believe it is the finest aviation headset you can own. This headset combines Bose Acoustic Noise Cancelling® headset technology to electronically reduce unwanted aircraft noise, and Bose TriPort® headset technology for a smaller, lighter, more comfortable headset that delivers full-spectrum noise reduction. We appreciate your choiceĬongratulations on your purchase of a Bose® Aviation Headset. The Interface pov,-ers the Headset’s active noise-reducing electronics and matches the Headset to the aircraft’s avionics. a Bose Aviation Headset must be connected 10a Bose Headset interface. As a result, this Headset can be worn comfortably for extended periods. The Bose Headset actively reduces noise elements in addition to 10 muffling noises. The Bose Aviation Headset uses a vanned combination of elective-acous1ical noise reduction circuitry and a pa1en1ed cushioning system 10 significantly reduce aircraft noise. An aircraft-powered headset will not operate properly if used with a Bose Series II Aviation Headset battery pack or with any commercial battery pack. If your headset is aircraft powered, connect the headset to the aircraft power sources only as described in this guide. If your headset is battery-powered, make sure it is connected only to battery power. Your headset is one of two types: battery-powered, or aircraft powered.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |